| 型号 | 品牌 | 功能应用 |
|---|
| MAX369C/D | MaximIC | Fault-protected analog multiplexer with latch. 4 channel differential (2 of 8). |
| MAX397EQI | MaximIC | Precision, dual 8-channel, low-voltage, CMOS analo0g multiplexer. |
| MAX4531C/D | MaximIC | Low-voltage, CMOS analog ICs configured as two 4-channel multiplexer. |
| MAX4265ESA | MaximIC | Single, ultra-low-distortion, single-supply, 300MHz op apm with enable. Min gain 1V/V, single-supply operation +4.5V to +8.0V |
| MAX6321HPUK30BY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX1293BCEG | MaximIC | 250ksps, +3V, 4-channel single-ended/2channel pseudo-differential, 12-bit ADC with +2.5V reference and parallel interface INL(LSB) +1,-1 |
| MAX6376UR31-T | MaximIC | Ultra-low-power voltage detector, 3.1V |
| MAX6317HUK46AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX163BCNG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX5151BCPE | MaximIC | Low-power, dual, 13-bit voltage-output DAC with serial interface. +3V single-supply operation. INL(LSB) +-2. |
| MAX6320PUK25BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX6318MHUK47CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX506AEWP | MaximIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-1 LSB. |
| MAX353ESE | MaximIC | Precision, quad, SPST analog switch |
| MAX4544EUT-T | MaximIC | Low-voltage, single-supply single SPDT analog switch. |
| MAX816ESA | MaximIC | +-1% accuracy, low-power, microprocessor supervisory circuit. Push-pull active-low reset output, push-pull active-high reset output, manual reset, power-fail monitor, Vcc reset voltage adjustable. |
| MAX483CPA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| OP07Z | MaximIC | Low offset voltage operational amplifier. |
| MAX6316LUK34BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX812LEUS-T | MaximIC | Microprocessor voltage monitor with manual reset input. Reset threshold voltage 4.63V. Push-pull active-high reset output. |
| MAX8216EJD | MaximIC | +-5V, +-15V dedicated microprocessor voltage monitor. |
| MAX6316MUK37DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.700V, min reset timeout 1120ms, typ watchdog timeout 1.6sec |
| MAX161CEPI | MaximIC | CMOS 8-bit 8-channel data acquisition system. Error 1/2 LSB |
| MAX6318MHUK47DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| ICM7224C/D | MaximIC | 4-1/2 digit counter |
| MAX755ESA | MaximIC | Negative output, inverting, current-mode PWM regulator. Converts +2.7V to +9V input to adjustable negative output. |
| MAX6309UK39D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.803(min),3.998(max) Nominal timeout period 140ms. |
| MAX9686MTV | MaximIC | Single very fast TTL output comparator |
| MAX6319MHUK40A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 1ms |
| MAX6316LUK30AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
