| 型号 | 品牌 | 功能应用 |
|---|
| MAX810MEUR-T | MaximIC | Microprocessor reset circuit. Reset threshold 4.38V. Push-pull active-high reset. 2.5k increments. |
| MAX492MJA | MaximIC | Dual, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp. |
| MAX6316MUK50DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
| MAX6317HUK32CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 140ms, typ watchdog timeout 102ms |
| DG442DJ | MaximIC | Improved, quad, SPST analog switch |
| MAX6713SEXS-T10 | MaximIC | Microprocessor reset circuit with manual reset input. Reset threshold 2.93V. Output type active-low open-drain reset. |
| MAX759C/D | MaximIC | Adjustable, inverting carrent-mode PWM regulator. |
| MAX6318MHUK39DY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| DG529AZ | MaximIC | 8-channel latchable multiplexer |
| MAX506BCWP | MaximIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-3/2 LSB. |
| MAX4174ABEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 0.25, 1+ (Rf/Dg) noninverting gain 1.25, -3dB BW 1700kHz. |
| MAX6316MUK44CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX490CSA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX875BCSA | MaximIC | Low-power, low-drift precision voltage reference. 5V+-3.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX900BCPP | MaximIC | High-speed, low-power voltage comparator |
| MAX630ESA | MaximIC | CMOS micropower step-up switching regulator |
| MAX6317HUK43CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX876BCPA | MaximIC | Low-power, low-drift precision voltage reference. 10V+-5.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX4663CPE | MaximIC | 2.5om, quad, SWPST, CMOS analog switch (two NC and two NO switches). |
| MXD1013C/D012 | MaximIC | 3-in-1 silicon delay line. Output delay 12ns. |
| MAX6316MUK37CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.700V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX4592EUE | MaximIC | High-speed, single-supply 12V, quad, SPST analog switches (four NO switches). |
| MAX4127C/D | MaximIC | Dual, wide-bandwidth, low-power, single-supply Rail-to-Rail I/O op amp. BW 5MHz. |
| MAX4665CPE | MaximIC | 5om, quad, SPST, CMOS analog switch (four NO switches). |
| MAX6315US46D1-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.63V. Reset timeout period(min) 1ms. |
| MAX6312UK39D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.803(min) 3.998(max). Nominal timeout period 1ms. |
| MAX810SEUR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 2.93V. Push-pull active-high reset. 10k increments. |
| MAX187AEWE | MaximIC | +5V, low-power, 12-bit serial ADC. Error(LSB) +-1/2. |
| ICL7650MJA | MaximIC | Chopper-stabilized amplifier |
| MAX793RCSE | MaximIC | Microprocessor supervisory circuit. Reset threshold 2.55V to 2.70V. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Battery OK output.Watchdog input.Manual reset inp. |
