| 型号 | 品牌 | 功能应用 |
|---|
| MAX7404ESA | MaximIC | 8-th-order, lowpass, elliptic, switched-capacitor filter. Filter response elliptic (r=1.5), operating voltage +3V |
| MX574AUD | MaximIC | Industry standard complete 12-bit A/D converter. 25 microsec. max conversion time. Linearity (LSBs) 3/4 TEMPCO(ppm/C) 12. |
| MAX709RESA | MaximIC | Power-supply monitor with reset. Reset threshold voltage 2.63V |
| MAX731EPA | MaximIC | 5V step-up current-mode DC-DC converter |
| MAX4167ESA | MaximIC | Dual, high-output-drive, precision, low-power, single-supply +2.7V to +6.5V, Rail-to-Rail I/O op amp. |
| MAX3131CAI | MaximIC | 3V to 5.5V, IrDA infrared transceiver with integrated RS-232 interface. |
| ICL7622DC/D | MaximIC | Dual operational amplifier, 15mV |
| MAX706TCSA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 3.08V. Active-low reset output signal. |
| MAX809JEUR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 4.00V. Push-pull active-high reset. 10k increments. |
| MAX6319LHUK36C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 140ms |
| MAX6318MHUK43CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX251MJD | MaximIC | +5V powered isolated RS-232 driver/receiver. |
| MAX4617CPE | MaximIC | Low-woltage, high-speed, CMOS analog IC configured as 8-channel multiplexer |
| MAX242CPN | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6313UK37D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.608(min) 3.793(max).Nominal timeout period 1120ms. |
| MX7847JN | MaximIC | Complete, dual, 12-bit multiplying DAC. 12-bit parallel interface. Error (LSB) +-1 |
| MAX6306UK34D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.315(min),3.485(max) Nominal timeout period 1ms. |
| MAX6318LHUK37DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.700V min, reset timeout 1.12sec,typ watchdog timeout 25.6sec |
| MAX2470EUT-T | MaximIC | 10 MHz to 500 MHz VCO buffer amplifier with differential outputs. |
| MAX1125BIBH | MaximIC | 8-bit,300 Msps flash ADC |
| MX7503SE | MaximIC | Low-power, monolithic, CMOS analog multiplexer. |
| MX7624EPE | MaximIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +12V to +15V. Error +-1/2 LSB |
| MAX4524EUB | MaximIC | Low-voltage, single-supply multiplexer and switch. |
| MAX4274AHESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz. |
| DG411DJ | MaximIC | Improved, quad, SPST analog switches |
| MAX211EWI | MaximIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MAX4275BAESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 10, 1+ (Rf/Dg) noninverting gain 11, -3dB BW 560kHz. |
| MAX6321HPUK47BX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX180BCQH | MaximIC | Complete, 8-channele, 12-bit data-acquisition system. Error(LSB) +-1. |
| MAX704MJA | MaximIC | Low-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.40V. |
