| 型号 | 品牌 | 功能应用 |
|---|
| MAX809TEUR-T | MaximIC | Microprocessor reset circuit. Reset threshold 3.08V. Push-pull active-high reset. 2.5k increments. |
| ICL7641CMJD | MaximIC | Quad operational amplifier, 10mV |
| MAX6353SYUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 2.93V (Vcc5) and 2.19V (Vcc3). Active-low push-pull reset 5V. Standard version. |
| MAX233AEWP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX4540CAP | MaximIC | Low-voltage, dual 4-to-1 calibration multiolexer. |
| MAX808LCSA | MaximIC | Supervisory circuit with +-1.5% reset accuracy. Reset threshold(typ) 4.675V. CMOS RAM write protection.. |
| MAX197AENI | MaximIC | Multi-range (+10V, +5V, +10V, +5V), single +5V, 12-bit DAS with 8+4 bus interface |
| MAX643AMJA | MaximIC | +15V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy |
| MAX6316LUK48DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1120ms, typ watchdog timeout 102ms |
| MAX2269EUE | MaximIC | 2.7V, single-supply, cellular-band linear power amplifier. Low average CDMA current consumption in typical urban scenario 50mA. TSSOP-EP 5mm x 6.4mm. |
| MAX6318LHUK35AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.500V min, reset timeout 1ms,typ watchdog timeout 102ms |
| MAX378EJE | MaximIC | High-voltage, fault-protected analog multiplexer. |
| MAX4074AFESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 1.5V/V, noninverting gain 2.5V/V, -3dB BW 180kHZ. |
| MAX876BC/D | MaximIC | Low-power, low-drift precision voltage reference. 10V+-5.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX199BCNI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX6318LHUK41DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.100V min, reset timeout 1.12sec,typ watchdog timeout 102ms |
| MAX529EWG | MaximIC | Octal, 8-bit, serial DAC with output buffer. Single +5V or dual +-5V supply operation. |
| MAX6318MHUK38CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6316LUK27AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.700V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX6320PUK33DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6316LUK35AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX744AC/D | MaximIC | 5V, step-down, current-mode PWM DC-DC converter accept inputs between 65V and 16V and deliver 750mA. 159kHz to 212.5kHz guaranteed oscillator frequency limits. |
| MAX510ACPE | MaximIC | Quad, serial 8-bit DAC with Rail-to-Rail output. TUE (LSB) +-1 |
| MAX6318LHUK41AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.100V min, reset timeout 1ms,typ watchdog timeout 25.6sec |
| MAX791C/D | MaximIC | Microprocessor supervisory circuit |
| MAX6317HUK30BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MX7501JN | MaximIC | Low-power, monolithic, CMOS analog multiplexer. |
| MXD1000UA30 | MaximIC | 5-tap silicon delay line |
| MAX6316LUK38BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX6316LUK28DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
